齿轮设计软件(Gear Geometry pro) v1.42 英文免装版

软件下载 7月 05, 2023 0 king

Gear Geometry pro是一款免装版的多功能齿轮设计软件，又称GearDesign，知识兔这款软件分享了多种测量方法显示，公制、英制单位互换等功能，知识兔可以满足不同设计师对齿轮设计的需要，并可以大大地提高设计师的效率，减少手工计算中造成的误差，需要此款工具的朋友们可以前来下载体验。

齿轮参数：
PINION→小齿轮 WHEEL→大齿轮
Normal Module (mm) →法向模数
Pressure Angle (degrees) →法向压力角
Helix Angle (degrees) →分度圆螺旋角
Helix Hand→螺旋旋向(left 左/right 右)
Centre Distance (mm) →中心距
Face Width (mm) →齿宽
Edge Chamfer (mm) →齿端倒角(棱)
Desired Ratio →要求的传动比
Number of Teeth→齿数
Sum of Add. Shift Coeff.→总变位系数(法向)
Add. Shift Coeff.→单个齿轮变位系数(法向)
Add. Shift Distribution→变位系数分配
nominal Thickness →公称齿厚
Backlash (Normal) (mm) →侧隙(法向)
Backlash Distribution →侧隙分配
Finished Thickness →成品齿厚
Outside Diameter (mm) →外径
Outside Diameter Chamfer (mm)→齿顶倒角(棱)(修缘)
Root Diameter (mm) →齿根直径
Root Fillet Radius (mm) →(齿条刀具)齿顶圆角半径
Basic Rack Proportions →基本齿条参数(输入/标准/计算)
Basic Rack Addendum (/Module) →基本齿条齿顶高系数
Basic Rack Dedendum (/Module) →基本齿条齿根高系数
Root Fillet Radius (/Module) →(基本齿条)齿根圆角半径系数
Protuberance →齿条刀具齿顶触角宽度
Allow Outside Diameter Reduction →允许齿顶圆减小
Keep Pinion and Wheel Same →保持两齿轮齿顶高相同计算结果：
PINION小齿轮
WHEEL大齿轮
Number of Teeth→齿数
Normal Module (mm) →法向模数
Pressure Angle (degrees) →法向压力角
Helix Angle (degrees) →分度圆螺旋角
Helix Hand →螺旋旋向(left 左/right 右)
Reference Diameter (mm)→分度圆直径
Addendum Modification Coeff. →变位系数(法向)
Outside Diameter (mm) →外径
Outside Diameter Chamfer (mm)→齿顶倒角(棱)(修缘)
Root Diameter (mm) →齿根直径
Root Fillet Radius (mm) →(齿条刀具)齿顶圆角半径
Centre Distance (mm) →中心距
Face Width (mm) →齿宽
Edge Chamfer (mm) →齿端倒角(棱)
Form Diameter (mm) →渐开线起始圆直径
Base Diameter (mm) →基圆直径
Thickness (nominal transverse) (mm) →(公称端面)齿厚
Thickness (nominal normal) (mm) →(公称法向)齿厚
Thickness (finished transverse) (mm) →(成品端面)齿厚
Thickness (finished normal) (mm) →(成品法向)齿厚
Measurement Over Balls(finished) (mm) →跨棒距
Ball Diameter (mm) →量棒直径
Chordal Span (mm) (finished) →(成品)公法线长度
Number of Teeth to Span →跨齿数
Contact Ratio (Transverse) →端面重合度
Contact Ratio (Axial) →轴向重合度
Desired Ratio →要求的传动比
Actual Ratio →实际传动比
Backlash (Transverse) (mm) →端面侧隙
Backlash (Normal) (mm) →法向侧隙
Backlash (Radial) (mm) →径向侧隙
Backlash (Transverse circular) (mm) →端面圆周侧隙
Backlash (Normal Circular) (mm) →法向圆周侧隙
start of active Profile Diameter (mm) →有效齿廓起始直径
Lowest Single Tooth Contact (mm) →单齿啮合最小直径
Highest Single Tooth Contact (mm) →单齿啮合最大直径
End of Active Profile Diameter (mm) →有效齿廓终止直径
Transverse Pressure Angle (deg) →端面压力角
Transverse Module (mm) →端面模数
Working Pitch Diameter (mm) →节圆直径
Working Normal Pressure Angle (deg) →法向啮合角
Working Transverse Pressure Angle (deg) →端面啮合角
Working Helix Angle (deg) →节圆螺旋角
Face Width Offset (mm) →齿宽调整
Active Face Width(mm) →有效齿宽
Base Radius to Form Radius (mm) →渐开线起始圆到基圆的距离
Form Radius to SAP Radius (mm) →有效渐开线起始圆到渐开线起始圆距离
Bottom Clearance / Module →顶隙系数
Normal EAP Thickness / Module →有效齿廓终止点法向厚度系数
Normal O.D. Thickness / Module →齿顶法向齿厚系数
Root Fillet Radius / Module →(齿条刀具)齿顶圆角半径系数
Base Helix Angle (degrees) →基圆螺旋角
Normal Base Pitch (mm) →法向基圆节距
Transverse Base Pitch (mm) →端面基圆节距
ISO Quality grade →ISO 精度等级
Single radial composite deviation (mm) →一齿径向综合公差
Total radial composite deviation (mm) →径向综合总公差
Single pitch deviation (mm) →单齿距公差
Total cumulative pitch deviation (mm) →齿距累积公差
Single tangential comp. deviation (mm) →一齿切向综合公差
Total tangential comp. deviation (mm) →切向综合总公差
Profile form deviation (mm) →齿廓形状公差
Profile slope deviation (mm) →齿廓倾斜极限偏差
Total profile deviation (mm) →齿廓总偏差的公差
Helix form deviation (mm) →螺旋线形状公差
Helix slope deviation (mm) →螺旋线倾斜极限偏差
Total helix deviation (mm) →螺旋线总偏差的公差
Tangential force (N) →圆周力
Radial force (N) →径向力
Axial force (N) →轴向力